- Description
- Document Center
Description
Stainless steel partition-mounted seat-cover dispenser and toilet tissue dispenser with satin finish
Features
- Stainless steel throughout with satin finish on all exposed surfaces; welded construction
- Mounts through partitions 1/2" to 2" (13-51mm) thick, serving two compartments, used from both sides, serviced from one side
- One side mounts flush against partition of barrier-free compartment to allow clearance for grab bar
- Flanges are one-piece seamless, door secured with full-length stainless steel hinges, and tumbler lock
- Toilet tissue on left when facing unit
- Theft-resistant spindles
Specifications
Materials: | Cabinet - 18-8 S, type-304, heavy-gauge stainless steel. All-welded construction. Exposed surfaces have satin finish. Equipped with a plastic sight-barrier panel for toilet-seat-cover dispenser Flanges - 18-8 S, type-304, 22-gauge (0.8mm) stainless steel with satin finish. Drawn and beveled, one-piece, seamless construction Door & Permanent Panel - 18-8 S, type-304, 18-gauge (1.2mm) stainless steel with satin finish. One-piece, seamless construction. Door is secured to cabinet with a full-length stainless steel piano-hinge and equipped with two tumbler locks keyed like other Bobrick washroom accessories Toilet Tissue Dispensers - .100" (2.5mm) thick ABS. Equipped with four theft-resistant, heavy-duty, one-piece, molded ABS spindles |
Size: | 17-3/16" (435mm) w x 30-5/8" (780mm) h x 4-5/16" (110mm) d |
Capacity: | Toilet-seat-cover dispenser - 1000 single- or half-fold paper covers Toilet Tissue Dispensers: four standard-core toilet tissue rolls up to 5-1/4" (135mm) diameter (1800 sheets), two for each compartment |
Operation: | Toilet-seat-cover dispenser is serviced from one side. Door unlocks with key provided and swings open for filling. Spindles may be removed from cabinet only when door is open; when door is closed, removal requires a special key provided for the concealed locking mechanism in spindles |
Installation: | Mount unit in toilet partition 1/2" to 3-7/8" (13 x 98mm) thick, centered through a cutout specially ordered from partition manufacturer or field cut. Dimensions of cutout are to be 15-1/2" wide x 28-7/8" high (395 x 735mm). Top of cutout should be 42-1/4" (1075mm) from finish face of floor with rear edge of cutout 20-1/2" (520mm) from back wall of compartment to allow placement of horizontal grab bar at 33" (840mm) height across front of unit. For factory-made cutouts, location and size details must be furnished to partition manufacturer. For hollow-core metal partitions, provide solid framing into which sheet-metal mounting screws can be secured For installation with sheet-metal screws furnished, place unit firmly in partition cutout, making certain entire perimeter of fixed flange is flush with and tight against Partition surface. Install the unit so the side that has the fixed flange flush with face of cabinet is in a barrier-free compartment for physically disabled persons. Secure to partition with sheet-metal screws through four mounting holes at points indicated by an S. On other side of partition, position adjustable flange (which serves as an escutcheon) so mounting holes are not inline with mounting holes in fixed flange. Make certain entire perimeter of adjustable flange is flush with and tight against partition surface before securing with sheet-metal screws furnished For through-bolting method of installation, make sure mounting holes in adjustable flange are inline with holes in fixed flange. Using adjustable flange as template to mark locations, drill 7/32" or 1/4" (5.5 or 6.4mm) holes through partition. Provide four binder posts and #6 (3.5mm) flat-head screws to secure unit and its adjustable flange. Obtain binder posts and screws by ordering Bobrick Binder Post Kit No. 354-119 for partitions 1/2" (13mm) thick only or Kit No. 354-124 for partitions 3/4" to 1-1/4" (19 to 32mm) thick Note: Cutouts in Bobrick toilet partitions can be pre-cut for Bobrick partition-mounted accessories at factory if location and size of cutouts are specified and order for both partitions and accessories are received together Designer's Note: on left side of toilet (when seated on toilet) rear edge of panel cut-out should be 32-1/2" to 34-1/2" (825 to 876mm from rear edge of panel to position toilet tisue dispensers centerline 7" to 9" (180 to 230mm) in front of leading edge of toilet. For units on right side of toilet, rear edge of panel cut-out should be 25" to 27" (635 to 685mm) from rear edge of panel Cut-out locations based on toilet projecting 30" (760mm) from rear wall, and a 1/2" (13mm) gap between rear edge of panel and rear wall |
Certifications
Barrier-Free Code Compliance: | Complies with barrier-free accessibility guidelines (including ADAAG in the U.S.A.) |
Document Center
>